Blow Molding Machine

MG-880 Semi-automatic Blow Molding Machine
MG-880 Semi-automatic Blow Molding Machine is improved its technology and design from the MG-5IIB type, and meets the standard of CE.
Microcomputer controlling and accurate control of the technical parameters.
Easy to control, safe, just need one person to control this machine without any training for this equipment.
MG-880 Semi-automatic Blow Molding Machine is used for producing carbonated beverage bottles, mineral water bottles, cosmetics bottles, hot filling bottles and Oil Bottle with handle.
Characteristic
1. Blowing 0.1-6 liter-PET bottles
2. Use two mold cavities for blowing 0.1 liter-bottles and this equipment can produce 850 bottles per hour
3. Advanced PLC control system, the time can be controlled precisely in 0.01 seconds
4. Air storage device
5. Infrared heater
6. Different heating lamp equipped with independent temperature control device, to ensure the best embryo
7. Heating lamp can be adjusted according to the direction of different bottles
8. It can be operated by one man, and no need any training
9. Easy to installation and startup
10. Scrap rate: below 0.3%.
Technical Data

Type	Item	Unit	Technical Parameter
Bottle Type	Material of bottle	/	PET/PP/PC/PE
	Cubage	L	5-6(2-cavity) 10-25(1-cavity)
	Theoretical Yield	Pcs/Hr	5gallon:120 5L:700
	Length	mm	15-460
Forming	Inner Diameter	mm	φ15-200
	Max. Acreage of Templet	mm	520×600
	Max. Thickness	mm	400
	Locking Power	KN	300
	Itinerary(Adjustable)	mm	330
Air press equipment	High Pressure Compressor	M3/MPa	≥0.60/3.0×1台
	Huffing Pressure	Mpa	2.0-4.0
	Low pressure compressor (Adjustable)	M3/MPa KW	≥0.8/1.25 7.5
Drier	Air Drier	M3/MPa KW	1.0/3.0
Main equipment Voltage	Power	KW	15
	Voltage / Frequency (Three-phase)	V/HZ	380-220/50-60 (三相)
Dimension and Weight	Main equipment overall dimension	M	2.60×1.90×1.95
	Weight	T	2.8
	Low pressure compressor	M	1.85×0.70×1.50
	High pressure compressor	M	1.90×0.75×1.50
	Inhaler	kg	10×2pcs
Safety guarantee	Automatic Alarm	Safety Locking System

Introduction:
MG-S2500 is one of the most fast beeline-type blow molding machines in mainland of China. Thanks to our experienced research team, MG-S2500 can produce over 1200 (350ML) bottles per hour. This equipment adopted independent baking tunnel and the blow station and it runs much more smoothly with good stability.
Technical specification of MGS-2500 Automatic Stretch Blow Molding Machine

Volume of product	0.1-2.5L
Product raw material	PET
Mould plate maximum dimension	420×500mm
Mould opening stroke	0.1-2L:150mm 6L(1caivty):250mm
Max mould thickness	0.1-2L:150mm 5L(1caivty):250mm
Clamping force	380KN
Air pressure for working	0.8-1.25Mpa
Air pressure for blowing	1.5-4.0Mpa
Temperature control	7 section
Length of pre-form	50-220mm
Inner diameter of pre-form tube	15-126mm
Stretching bar diameter	8-50mm
Quantity of heating rotation	34-60pcs
Length of bottle	340mm
Diameter of bottle	60-220mm
Power	23KW
Temperature in the pre-form	3.5KW
weight	2600kgs
Main machine dimensions (L×W×H)	316×225×226cm
Weight of conveyer	400KGS
Conveyer dimensions	200×190×226cm
Electric voltage/Frequency	220V/380/50Hz

Pneumatic parts for MGS-2500 machine

NO	ITEM	IMPORTED FORM
1	Main cylinder for Clamping	FESTO/Germany
2	Stretching Cylinder	FESTO/Germany
3	Solenoid valve for High pressure 2pcs	FESTO/Germany
4	Solenoid valve for Low pressure 2pcs	FESTO/Germany
5	PLC Controller	TIANJING
6	Water divide	SMC/JAPAN
7	Oil divide	SMC/JAPAN
8	Lubrication	Automatic
9	Temperature controller	It is special design form China famous company
10	Blow pipe	China it can bear 80kgs, actually we only use 30kgs.

MG-90 PET stretch blow molding machine is specially designed to produce 5-gallon bottle and 25L jar. Its max output is up to 90 BPH for 5-gallon bottle and even could reach 120 bottles per hour in certain case.
MG-90 consists of main unit and rotary infrared heater. The ordinary quartz lamp cannot heat preform ideally because the preform wall is excessively thick. The infrared heater with high penetrative force can heat the inside and outside of preform simultaneously and keep preform in even heating, therefore high shaping quality. blow moulder, blow molder
Characteristic
1. Blowing 6 liter-PET bottles
2. Use two mold cavities for blowing 0.1 liter-bottles and this equipment can produce 850 bottles per hour
3. Infrared heater
4. Adopt double heating up system, to ensure 730gram-Thick bottle can have a good thick-walled bottle.
5. Equipped with special inner cooling system, to ensure the best embryo
6. Cooling system ensures the quality of bottle neck
7. Use separated mould, and it can produce 90 (five gallon) bottles per hour
8. Advanced PLC control system, the time can be controlled precisely in 0.01 seconds
9.. Air storage device
10. Easy to installation and startup
Technical Data

Item	Item	Unit	Technical Parameter
Material of bottle Cubage Theoretical Yield Length Inner Diameter	Material of bottle	/	PET/PC/PE
	Cubage	L	5-6(2-cavity) 10-25(1-cavity)
	Theoretical Yield	Pcs/Hr	5gallon:90,5L:400
	Length	mm	15-460
	Inner Diameter	mm	φ15-200
Max. Acreage of Templet Max. Thickness Locking Power Itinerary(Adjustable)	Max. Acreage of Templet	mm	420×500
	Max. Thickness	mm	400
	Locking Power	KN	330
	Itinerary(Adjustable)	mm	330
High Pressure Compressor Huffing Pressure Low pressure compressor (Adjustable)	High Pressure Compressor	M3/MPa	≥0.60/3.0
	Huffing Pressure	MPa	2.0-3.0
	Low pressure compressor (Adjustable)	M3/MPa/KW	≥0.8/1.25/7.5
Air Drier Power	Air Drier	KW	15
	Power	V/HZ	380-220/50-60 (3-phase)
Voltage / Frequency (Three-phase) Main equipment overall dimension Weight Low pressure compressor High pressure compressor	Voltage / Frequency (Three-phase)	M	1.55×0.82×2.00
		T	1
	Main equipment overall dimension	M	2.42×0.65×1.60
	Weight	T	0.38
	Low pressure compressor	M	1.90×0.75×1.50
	High pressure compressor	kg	10×2pcs
Inhaler	Inhaler	Safety Locking System